![]() ![]() Run_seconds: # List of station index and run seconds pairs (required) Run_seconds: # Seconds to run for each station (required) service: nĮntity_id: ntroller_name # Switches or sensors for controller The following examples are all equivalent. Run_seconds: # Dictionary of station index and run seconds key/value pairs (required)īy default running once program will stop all other stations that are running, you can specifyĬontinue_running_stations to true to allow the stations to continue running. service: nĬontinue_running_stations: True # Whether to keep running stations running (optional, defaults to False) service: nĬontinue_running_stations: True # Whether to keep running stations running (optional, defaults to False) Stop Examples Stop Station Example service: opensprinkler.stopĮntity_id: switch.station_name # Switches or sensors for stations Stop All Stations Example service: opensprinkler.stopĮntity_id: ntroller_name # Switches or sensors for controller Creating a Station Switch Specifying the run seconds in index/second pairs. If you wish to have a switch for your stations, here is an example using the switch template and input number.Īdd the following to your YAML configuration ( configuration.yaml). Value_template: ""Įntity_id: binary_sensor.This binding allows good and flexible control over your OpenSprinkler devices. ![]() You can choose to manually start, stop or delay the stand alone watering programs that are stored and run fully from the OpenSprinkler device.Īlternatively you can setup openHAB rules to control everything in more depth by setting up multiple station things for each watering zone to gain more in depth control.īy using the internal programs and sensors of the OpenSprinkler device, it can remove the complexity of what happens to the watering if openHAB crashes, is rebooted, or drops out of WiFi range in the middle of your watering rules. OpenSprinkler Station is for gaining advanced controls and status information over a single station (zone) of a device, e.g.OpenSprinkler HTTP Bridge is required to communicate with an OpenSprinkler device through the network and should be added first.Mixing the two concepts can also be done, the choice is yours. Generation 5 SonicWall or Generation 6 (SOHOW, TZ series) SonicWall or Generation 7 (TZ series)īegin the process of configuring the SonicWall manually, as if it were new.OpenSprinkler Device is for device-specific controls that usually apply to multiple stations or main unit sensors, e.g.to turn it on or off, or the time remaining. If you're unsure how to do this, reference Entering Safe Mode from both the GUI and Command Line Interface. Solution 2: Factory Default the SonicWall and Rebuild the Settings Manually When the SonicWall reboots it will still require the Credentials of admin | password, this can be changed by navigating to System | Administration. Register the SonicWall by following the prompt in the upper right-hand corner of the GUI.ĬAUTION: If you cannot register the SonicWall due to a DNS Error navigate to Network | DNS and set the SonicWall DNS for any public DNS Server (8.8.8.8 | 4.2.2.2).SonicWall Default IP Address: 192.168.168.168.Īdministration Credentials: admin | password. Generation 5 SonicWall or Generation 6 (SOHOW, TZ series) SonicWall or Generation 7 (TZ series) Connect to the SonicWall with the following method and credentials.Boot the SonicWall to the current firmware (or an Upgraded Firmware) with Factory Default Settings.Solution 1: Factory Default the SonicWall and Import a Supported Settings File If the administration credentials for a SonicWall are misplaced then there are only two options available, as presented below. ![]() While this has the downside of potentially locking an administrator out of their device, the benefit of a hardened and secure network outweigh these concerns. SonicWall appliances are first and foremost security devices, meaning they are not programmed with backdoors or other exploitable methods of access. When this occurs there is no way to reset the password or discover it as an administrator, nor can SonicWall technical support provide any reset or recovery for lost administration credentials. ![]() In some instances the administrator user name or password for the SonicWall appliance may be lost or corrupted.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |